Jump to content

NZASM 40 Tonner 0-6-2T

From Wikipedia, the free encyclopedia
(Redirected from CSAR Class A 0-6-2T)

NZASM 40 Tonner 0-6-2T
CSAR Class A 0-6-2T
40 Tonner no. 50 S.W. Burger, Komatipoort, c. 1895
Type and origin
Power typeSteam
DesignerMaschinenfabrik Esslingen
BuilderMaschinenfabrik Esslingen
Serial numberEsslingen 2436–2445, 2480–2489
Build date1891–1892
Total produced20
Specifications
Configuration:
 • Whyte0-6-2T
 • UICC1n2t
Driver2nd coupled axle
Gauge3 ft 6 in (1,067 mm) Cape gauge
Coupled dia.51+316 in (1,300 mm)
Trailing dia.31+12 in (800 mm)
Wheelbase18 ft 10+38 in (5,750 mm) ​
 • Axle spacing
(Asymmetrical)
1–2: 5 ft 10+332 in (1,780 mm)
2–3: 5 ft 3+2532 in (1,620 mm)
 • Coupled11 ft 1+78 in (3,400 mm)
Length:
 • Over couplers33 ft 6+12 in (10,224 mm)
Height12 ft 4+1132 in (3,768 mm)
Frame typePlate
Axle load9.98 LT (10,140 kg) ​
 • Coupled9.98 LT (10,140 kg)
 • Trailing9 LT 12 cwt (9,754 kg)
Adhesive weight29.94 LT (30,420 kg)
Loco weight39.54 LT (40,170 kg)
Fuel typeCoal
Fuel capacity2 LT 12 cwt (2.6 t)
Water cap.1,525 imp gal (6,930 L)
Firebox:
 • TypeRound-top
 • Grate area16.4 sq ft (1.52 m2)
Boiler:
 • Pitch5 ft 9+932 in (1,760 mm)
 • Diameter3 ft 9+932 in (1,150 mm)
 • Tube plates12 ft 8+34 in (3,880 mm)
 • Small tubes144: 1+2532 in (45 mm)
Boiler pressure160 psi (1,103 kPa)
Heating surface:
 • Firebox101.2 sq ft (9.40 m2)
 • Tubes845 sq ft (78.5 m2)
 • Total surface946.2 sq ft (87.90 m2)
CylindersTwo
Cylinder size16+1516 in (430 mm) bore
24+1316 in (630 mm) stroke
Valve gearHeusinger
Valve typeMurdoch's D slide
CouplersJohnston link-and-pin
Performance figures
Tractive effort16,707 lbf (74.32 kN) @ 75%
Career
OperatorsNZASM
Selati Railway
Imperial Military Railways
Central South African Railways
ClassNZASM 40 Tonner
CSAR Class A
Number in class20
NumbersNZASM 41-60, CSAR 1-19
Official name40 Tonner
Delivered1892–1893
First run1892

The NZASM 40 Tonner 0-6-2T of 1892 was a South African steam locomotive from the pre-Union era in Transvaal.

In 1892 and 1893, the Nederlandsche-Zuid-Afrikaansche Spoorweg-Maatschappij (NZASM) of the Zuid-Afrikaansche Republiek (Transvaal Republic) placed twenty 0-6-2T locomotives in mainline service. Since the railway classified its locomotives according to their weight, these locomotives were known as the 40 Tonners.[1][2]

Manufacturer

[edit]

Although the completion of the line from Delagoa Bay to Pretoria was still more than three years in the future, a requirement for larger and heavier mainline locomotives was identified in 1891. The Nederlandsche-Zuid-Afrikaansche Spoorweg-Maatschappij (NZASM) therefore ordered ten 0-6-2T tank locomotives from Emil Kessler's Maschinenfabrik Esslingen. A second order for another ten followed later in 1891.[1][3]

The first batch of locomotives were delivered in 1892, numbered in the range from 41 to 50. Of the second batch, numbered in the range from 51 to 60, the last seven were built in 1892. Since the NZASM classified its locomotives according to their weight, these locomotives were known as the 40 Tonners. In addition to being numbered, they were all named as well, with the names and numbers cast in brass and mounted on their tank sides.[1]

Characteristics

[edit]

The locomotive used Murdoch's D unbalanced slide valves, arranged horizontally above the cylinders outside the plate frames and actuated by Heusinger valve gear. These valves caused considerable wear on motion pins and were later replaced by Trick ported balanced slide valves.[1][2]

The boiler barrel was built up in three rings, arranged telescopically, with the smallest diameter at the firebox end. The rings were lap-jointed and double riveted on longitudinal seams. These boilers had a long life and required little expense in repairs. Five cross-stays were fitted in the steam space above the firebox. The safety valves were arranged above the firebox inside the cab, while a steam escape pipe was fitted above the valves and passed through the roof.[2]

The exhaust had an Adams' Vortex pattern annular nozzle. While this presented additional surface to the blast, the annular orifice had a tendency to become clogged, which increased back pressure, and the exhaust pipes therefore frequently had to be taken out for cleaning. As delivered, the locomotive had 5 inches (127 millimetres) thick wooden buffer beams which were later replaced by 1 inch (25 millimetres) thick steel plates.[2]

The distance between the locomotive's tyres, i.e. between the wheel flanges on the axle, was 3 feet 3+38 inches (1,000 millimetres). This was 38 inch (10 millimetres) greater than for engines of the Cape Government Railways and Natal Government Railways and, although the flanges were somewhat thinner, the resulting tightness to gauge was blamed for the rather high rate of flange wear. To obtain greater life from the leading coupled wheels, they were occasionally exchanged with the trailing coupled wheels during overhauls.[2]

The original coupled axles were 5+14 inches (133 millimetres) in diameter and were inclined to fracture. This was remedied by increasing the diameter to 5+34 inches (146 millimetres) on new axles. The trailing wheels also proved to be troublesome. The trailing wheels and axle were of the radial type and were attached directly to the frame, which gave the locomotive a rigid wheelbase. The problem arose as a result of insufficient sideward freedom of movement of the trailing axle when the locomotive traversed sharp curves and diverging points.[1][2]

Service

[edit]

NZASM

[edit]

The 40 Tonners were found to be satisfactory in service, but the absence of leading carrying wheels resulted in a rough ride.[1]

Selati Railway

[edit]

In June 1890, Eugene, the younger of the Barons Oppenheim, sought to obtain a concession from the Government of the Zuid-Afrikaansche Republiek to construct a railway line to the Murchison Range goldfields along the Selati River. Work on the construction of the Selati Railway in the Transvaal Lowveld began early in 1893, with the line branching off from the Pretoria-Delagoa Bay mainline at a junction near Komatipoort. The two locomotives Durban and Pietermaritzburg were purchased from the Natal Government Railways for use during construction, as well as two 40 Tonners which were acquired from the NZASM.[1][4]

The project was abandoned in 1894, due to financial difficulties as well as a dispute which arose with the NZASM over the chosen route. Work on the railway was only resumed and completed by the Central South African Railways (CSAR) in 1909. The line was then extended via Gravelotte and Tzaneen to a junction at Soekmekaar, where it met the line from Pietersburg to Messina in 1912. In 1963, the part of the line through the southern part of the Kruger National Park, from the junction near Komatipoort, was abandoned and replaced by a new line from the present junction near Kaapmuiden.[1][4][5]

Imperial Military Railways

[edit]

In 1899, during the Second Boer War, all railway operations in the two Boer Republics, the ZAR and the Orange Free State, were taken over by the Imperial Military Railways (IMR). Nineteen of the 40 Tonners survived the war.[1][3]

Central South African Railways

[edit]

At the end of the war, when the IMR was transformed into the CSAR, the nineteen surviving 40 Tonners were designated Class A and renumbered in the range from 1 to 19. None survived in railway service to be taken onto the South African Railways roster in 1912.[1][6]

Works numbers

[edit]

The 40 Tonner engine numbers, names, works numbers and years built are listed in the table.[1]

Illustration

[edit]

The main picture shows no. 50, the S.W. Burger, on a mixed train at Komatipoort. The picture of the same engine below offers a side view of the 40 Tonner locomotive.

The second picture below offers an overhead view of a 40 Tonner, either no. 55 Van Riebeeck or no. 57 Pretorius, after the Braamfontein disaster of 1896. One of the worst explosions in the history of South Africa occurred at Braamfontein station, Johannesburg, on 19 February 1896. An explosives train carrying between 56 and 60 tons of dynamite, which had been standing in searing heat for 3½ days, was struck by a shunting train and exploded. The blast left a crater 60 metres (197 feet) long, 50 metres (164 feet) wide and 8 metres (26 feet) deep and was heard in Klerksdorp, 200 kilometres (124 miles) away. The exact number of casualties was never ascertained, but at least 62 people were killed and more than 200 seriously injured. Surrounding suburbs as far as Fordsburg were partially destroyed. Some 3,000 people lost their homes and almost every window in the town was shattered.[7]

References

[edit]
  1. ^ a b c d e f g h i j k Holland, D.F. (1971). Steam Locomotives of the South African Railways. Vol. 1: 1859–1910 (1st ed.). Newton Abbott, England: David & Charles. pp. 113–114, 116, 121, 126. ISBN 978-0-7153-5382-0.
  2. ^ a b c d e f Espitalier, T.J.; Day, W.A.J. (1944). The Locomotive in South Africa – A Brief History of Railway Development. Chapter IV – The N.Z.A.S.M. (Continued). South African Railways and Harbours Magazine, November 1944. pp. 844–845, 848.
  3. ^ a b The South African Railways – Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, p. 20, 22–23.
  4. ^ a b Artefacts – Selati Line, Skukuza District, Mpumalanga (Accessed 25 February 2016)
  5. ^ Reader's Digest Atlas of Southern Africa, The Reader's Digest Association South Africa (Pty.) Limited, 1984, (Editor Christoper Walton), p182, ISBN 0 947 008 020
  6. ^ Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer's Office, Pretoria, January 1912, p. 2 (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)
  7. ^ The Great Dynamite Explosion, report by Mr. J.G. Blumberg, Fairmount School, Johannesburg, excerpt from the autobiography of Dutch immigrant Jan de Veer who came to South Africa in 1893.