Talk:L pad

This is the talk page for discussing improvements to the L pad article.
This is not a forum for general discussion of the article's subject.

Put new text under old text. Click here to start a new topic.
New to Wikipedia? Welcome! Learn to edit; get help.

Article policies

Find sources: Google (books · news · scholar · free images · WP refs) · FENS · JSTOR · TWL

Professional sound production Low‑importance

	This article is within the scope of WikiProject Professional sound production, a collaborative effort to improve the coverage of sound recording and reproduction on Wikipedia. If you would like to participate, please visit the project page, where you can join the discussion and see a list of open tasks.Professional sound productionWikipedia:WikiProject Professional sound productionTemplate:WikiProject Professional sound productionProfessional sound production articles
Low	This article has been rated as Low-importance on the project's importance scale.

Electronics Mid‑importance

	Electronics portal This article is part of WikiProject Electronics, an attempt to provide a standard approach to writing articles about electronics on Wikipedia. If you would like to participate, you can choose to edit the article attached to this page, or visit the project page, where you can join the project and see a list of open tasks. Leave messages at the project talk pageElectronicsWikipedia:WikiProject ElectronicsTemplate:WikiProject Electronicselectronic articles
Mid	This article has been rated as Mid-importance on the project's importance scale.

"Rheostats" or "Potentiometer"

A recent editor changed "An L pad is a special configuration of rheostats" to "...special configuration of potentiometer" (emphasis added). I've reverted this because I disagree with this change on several counts:

It's still conventional to refer to the two-terminal device as a "rheostat". You'll even see potentiometers referred to as "rheostats" when the wiper is shorted to one end so that the pot operates purely as a variable resistor and not as a voltage (potential) divider.
The editor made potentiometer singular. Grammar aside...
There's no configuration of a single potentiometer possible that performs the function of an L-Pad.

Atlant 19:02, 12 February 2007 (UTC)[reply]

Traditionally, the word rheostat was used to refer to a variable resistor in DC applications. Potentiometer was used for AC applications including audio, where the device presented an impedance (resistance plus reactance). Common usage over the years has of course mangled this distinction. I don't have time to track this down and verify it, so help yourself. ... Kenosis 19:59, 12 February 2007 (UTC)[reply]

Switched L pad

There are also switched networks using fixed Rs and typically a rotary switch.

—Preceding unsigned comment added by Tabby (talk • contribs)

Please feel free to be bold and add this to the article!

Atlant (talk) 17:29, 3 January 2008 (UTC)[reply]

Valves vs. transistors

"This constant-impedance load was important in the days of vacuum tube power amplifiers because such amplifiers often did not work efficiently when terminated into an impedance greatly different than their specified output impedance. Maintaining constant impedance is less important to modern amplifiers using solid state electronics, so L pads are rarely seen today."

Is this really valid? Tabby (talk) 05:28, 3 January 2008 (UTC)[reply]

Umm, yes? Why do you not think so? Seriously, transistor amps have output impedances that are a small fraction of an ohm so they're happy driving any nearly-resistive load across a wide range of impedances. This was definitely not true for vacuum tube amps; for example, they had a nasty habit of roasting the screens on their output tubes if you tried to run them into too-high an impedance. Hence the L-pad; that substituted more and more of a dummy load as it inserted more and more resistance into the speaker path.

Atlant (talk) 17:27, 3 January 2008 (UTC)[reply]

Origins of name?

It is unclear what the origins of the 'L' are. The first sentence implies that it comes from 'Loss' Pad or 'Losser' Pad, however it later states that the name comes from the arrangement of the resistors...? —Preceding unsigned comment added by 77.100.216.53 (talk) 20:37, 5 April 2009 (UTC)[reply]

I thought it should for Level as in sound level. Constant314 (talk) 23:38, 13 December 2010 (UTC)[reply]

By analogy with T and Pi pads, I would assume it's the circuit topology. Dicklyon (talk) 21:16, 28 December 2010 (UTC)[reply]

No matter what it used to mean, it certainly means a circuit that looks like an "L" now.Constant314 (talk) 20:03, 29 December 2010 (UTC)[reply]

Proposing making introduction more general and moving the speaker related information to a section

The introduction starts off defining the L-pad as device specifically for controling the volume of a speaker. But then there are later sections that deal with applications that are not related to speakers. I would like to make the introduction general enough to cover all the included information and move the speaker related information to its own section. Nothing would be lost or changed.Constant314 (talk) 03:06, 17 December 2010 (UTC)[reply]