User:Chatul/sandbox/ISA

This is a replacement for the following sections of Comparison of instruction set architectures

• Base
  • Bits
  • Operands
  • Encoding length
  • Endianness

Data representation

In the early decades of computing, there were computers that used binary, decimal and even ternary. Contemporary computers are almost exclusively binary.

Characters are encoded as strings of bits or digits, using a wide variety of character sets; even within a single manufacturer there were character set differences.

Integers are encoded with a variety of representations, including Sign_magnitude, Ones' complement, Two's complement, Offset binary, Nines' complement and Ten's complement.

Similarly, floating point numbers are encoded with a variety of representations for the sign, exponent and mantissa. In contemporary machines IBM hexadecimal floating-point and IEEE 754 floating point have largely supplanted older formats.

Addresses are typically unsigned integers generated from a combination of fields in an instruction, data from registers and data from storage; the details vary depending on the architecture.

Bits

Computer architectures are often described as n-bit architectures. In the first 3⁄4 of the 20th century, n is often 12, 18, 24, 30, 36, 48 or 60. In the last 1⁄3 20th century, n is often 8, 16, or 32, and in the 21st century, n is often 16, 32 or 64, but other sizes have been used (including 6, 39, 128). This is actually a simplification as computer architecture often has a few more or less "natural" data sizes in the instruction set, but the hardware implementation of these may be very different. Many instruction set architectures have instructions that, on some implementations of that instruction set architecture, operate on half and/or twice the size of the processor's major internal datapaths. Examples of this are the Z80, MC68000, and the IBM System/360. On these types of implementations, a twice as wide operation typically also takes around twice as many clock cycles (which is not the case on high performance implementations). On the 68000, for instance, this means 8 instead of 4 clock ticks, and this particular chip may be described as a 32-bit architecture with a 16-bit implementation. The IBM System/360 instruction set architecture is 32-bit, but several models of the System/360 series, such as the IBM System/360 Model 30, have smaller internal data paths, while others, such as the 360/195, have larger internal data paths. The external databus width is not used to determine the width of the architecture; the NS32008, NS32016 and NS32032 were basically the same 32-bit chip with different external data buses; the NS32764 had a 64-bit bus, and used 32-bit register. Early 32-bit microprocessors often had a 24-bit address, as did the System/360 processors.

Endianness

An architecture may use "big" or "little" endianness, or both, or be configurable to use either. Little-endian processors order bytes in memory with the least significant byte of a multi-byte value in the lowest-numbered memory location. Big-endian architectures instead arrange bytes with the most significant byte at the lowest-numbered address. The x86 architecture as well as several 8-bit architectures are little-endian. Most RISC architectures (SPARC, Power, PowerPC, MIPS) were originally big-endian (ARM was little-endian), but many (including ARM) are now configurable as either.

Endianness only applies to processors that allow individual addressing of units of data (such as bytes) that are smaller than some of the data formats.

Instruction formats

Opcodes

In some architectures, an instruction has a single opcode. In others, some instructions have an opcode and one or more modifiers. E.g., on the IBM System/370, byte 0 is the opcode but when byte 0 is a B2₁₆ then byte 1 selects a specific instruction, e.g., B205₁₆ is store clock (STCK).

Operands

Addressing modes

Architectures typically allow instructions to include some combination of operand addressing modes

Direct

The instruction specifies a complete (virtual) address

Immediate

The instruction specifies a value rather than an address

Indexed

The instruction specifies a register to use as an index. In some architecture the index is scaled by the operand length.

Indirect

The instruction specifies the location of a word that describes the operand, possibly involving multiple levels of indexing and indirection.

Truncated

Base-displacement

The instruction specifies a displacement from an address in a register

autoincrement/aurodecrement

A register used for indexing is incremented or decremented by 1, an operand size or an explicit delta

Number of operands

Main article: instruction set § Number of operands

The number of operands is one of the factors that may give an indication about the performance of the instruction set. A three-operand architecture (2-in, 1-out) will allow

A := B + C

to be computed in one instruction

ADD B, C, A

A two-operand architecture (1-in, 1-in-and-out) will allow

A := A + B

to be computed in one instruction

ADD B, A

but requires that

A := B + C

be done in two instructions

MOVE B, A
ADD C, A

Encoding length

As can be seen in the table below some instructions sets keep to a very simple fixed encoding length, and other have variable-length. Usually it is RISC architectures that have fixed encoding length and CISC architectures that have variable length, but not always.