User:Bytesock/3Com 3c509
3Com 3c509 is a line of Ethernet IEEE 802.3 network cards for the ISA, EISA, MCA and PCMCIA computer buses.[1] It's designed by 3Com, and was put on the market in 1994.[1][2]
Features
[edit]The 3Com 3c5x9 family of network controllers have different interface combinations of computer bus like ISA, EISA, MCA and PCMCIA. And for network connection uses 10BASE-2, AUI and 10BASE-T.
Physical card configurations
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
B = On ISA and PCMCIA adapter numbers indicates that these adapters are part of the second generation of the Parallel Tasking™ EtherLink III technology.[1] |
The DIP-28 (U1) EPROM for network booting may be 8, 16 or 32 kByte size.[1] This means EPROMs of type 64, 128, 256 kbit (2^10) are compatible, like the 27C256.
Boot ROM address is located between 0xC0000 - 0xDE000.[1]
Teardown example, the 3c509B-Combo
[edit]The Etherlink III 3C509B-Combo is registred with the FCC ID DF63C509B. The main components on the card is Y1: crystal oscillator 20 MHz , U50: coaxial transceiver interface DP8392, U4: main controller 3Com 9513S (or 9545S etc), U6: 8 kByte 70 ns CMOS static RAM, U1: DIP-28 27C256 style EPROM for boot code, U3: 1024 bit 5V CMOS Serial EEPROM (configuration).
-
3C509B-Combo 1994 ASSY 03-0021-001 REV-A
-
3C509B-Combo 1996 ASSY 03-0021-004 REV-B
Label:
Etherlink III (C) 1994 3C509B-C ALL RIGHTS RESERVED ASSY 03-0021-001 REV-A FCC ID: DF63C509B
Barcode:
EA=0020AFDCC34C SN=6AHDCC34C MADE IN U.S.A.
R = Resistor C = Capacitor L = Inductance Q = Transistor CR = Transistor FL = Transformer T = Transformer U = Integrated circuit J = Jumper or connector VR F
FL70: Pulse transformer
bel9509 A 0556-3873-03 * HIPOTTED
Y1: 20 MHz crystal
20.000M 652DA
U50:
P9512BR DP8392CN Coaxial Transceiver Interface
T50: Pulse transformer, pinout: 2x8
VALOR ST7033
x00: Pulse transformer
VALOR PT0018 CHINA M 9449 C
U4: Plastic package 33x33 pins
Parallel Tasking TM 3Com 40-0130-002 9513S 22050553 AT&T 40-01302
Another chip with the same function:
40-0130-003 9545S 48324401 AT&T 40-01303
U6: 8192 x 8-bit 70 ns CMOS static RAM
HY 6264A LJ-70 9509B KOREA
Another chip with the same function:
CY6264-70OSC (photo)
U1: Boot ROM
DIP-28 EPROM 8,16, or 32 kB (27/28C256) for boot code.
U3: 256 Bit/1K 5.0V CMOS Serial EEPROM
B 52AH 93C46 M8
Q41: N-Channel Logic level Power MOSFET 60V, 11A, 107 mΩ (using ASSY 03-0021-004 due to obscured view)
F3055L 96 45 (H)H
VR41: 3-Terminal 0.5 A Negative Voltage Regulator (-5V) in D2PAK
KA79 M05
ASSY 03-0021-004 REV-B has written on it: U.S. Patents: U.S. patent 5,307,459
|}
Connector for the computer bus: ISA 16-bit
Connections for networking: 10BASE-T (8P8C), AUI (DA-15), 10BASE2 (BNC)
Driver setup
[edit]Some of the possible ISA I/O bases are 0x280, 0x300, 0x310, 0x320, 0x330, 0x340, 0x350. And IRQ 5, 7, 9, 10, 11, 12. The driver for OpenBSD[3], NetBSD and FreeBSD[4] is "ep",[5] For Linux it's "eth".[6][7]
Patents
[edit]U.S. Patents: U.S. patent 5,307,459 with priority date 1992-07-28.
This patent describes a method where a data transfer counter triggers a threshold logic that generates an early indication or interrupt signal before the transfer is completed. The adapter also writes timing information into status registers such that a device driver can optimize for any latency.
Uses
[edit]- PC/TCP Packet Driver for use with MS-DOS or PC-DOS on X86
- Amiga networking (Miami Network Interface MNI, gg2-3c509.mni)
See also
[edit]- Ethernet
- AMD Lance Am7990 - 1985, AMD Am7990 network chip
- NE2000 - 1987, Novell's NE2000 network card
- RTL8139 - 1999, Realtek 8139 PCI network chip
External links
[edit]- jaapsch.net - 27C256 256K (32K x 8) CMOS EPROM
- PIC18F452 and 3COM 3C509B Ethernet ISA card, Controlling a ISA 16-bit network card with a PIC18F452
- Workaround to install NE2000 / 3C509 Non Plug&Play ISA Network Adapters (2002)
References
[edit]- ^ a b c d e f "EtherLink® III Parallel Tasking™ ISA, EISA, Micro Channel®, and PCMCIA, Adapter Drivers Technical Reference, Members of the 3Com EtherLink III family of adapters" (PDF) (published 2011-08-29). August 1994. Retrieved 2016-04-06. (PDF)
- ^ "3Com 3C509B-TPO - WikiDevi". 2014-09-12. Retrieved 2016-04-06. (HTML)
- ^ https://github.com/openbsd/flashboot/commit/32e5b6bc2368fd39594a884aa318e5c8c3986ff1 "+ep* at isa? # 3C509 ethernet"
- ^ http://www.berklix.com/jhs/scanjet/dmesg/4.11 "ep0: <3Com 3C509-Combo EtherLink III> at port 0x300-0x30f irq 10 on isa0"
- ^ http://www.fml.org/home/fukachan/NetBSD/benchmarks/wintermute/dmesg.txt "ep0 at isa0 port 0x300-0x30f irq 10: 3Com 3C509 Ethernet"
- ^ https://sourceforge.net/p/leaf/mailman/message/12008019/ eth0: 3c509 at 0x300 tag 1, 10baseT port, address 00 60 97 69 32 3f, IRQ 5. I/O: 0x300, 0x310, 0x320, 0x330, 0x340, 0x350 IRQ: 5, 7, 9, 10, 11, 12
- ^ http://www.gossamer-threads.com/lists/linux/kernel/72450 eth0: 3c509 at 0x280 tag 1, 10baseT port, address 00 a0 24 1f 32 02, IRQ 9.