Nipple (plumbing)

In plumbing and piping, a nipple is a fitting, consisting of a short piece of pipe, usually provided with a male pipe thread at each end, for connecting two other fittings.

The length of the nipple is usually specified by the overall length with thread. It may have a hexagonal section in the center for a wrench to grasp (sometimes referred to as a "hex nipple"), or it may simply be made from a short piece of pipe (sometimes referred to as a "barrel nipple" or "pipe nipple"). A "close nipple" has no unthreaded area; when screwed tightly between two female fittings, very little of the nipple remains exposed. A close nipple can only be unscrewed by gripping one threaded end with a pipe wrench which will damage the threads and necessitate replacing the nipple, or by using a specialty tool known as a nipple wrench (or known as an internal pipe wrench) which grips the inside of the pipe, leaving the threads undamaged. When the ends are of two different sizes it is called a reducer or unequal nipple.

Threads used on nipples are BSP, BSPT, NPT, NPSM and Metric.

Chase nipple

A chase nipple is a short pipe fitting, which creates a path for wires between two electrical boxes. A chase nipple has male threads on one end only. The other end is a hexagon. The chase nipple passes through the knockouts of two boxes, and is secured by an internally threaded ring called a lock nut.^[1]^[2]

Chase-Shawmut Company, of Boston, is the company which first produced chase nipples.^[3]

References

^ Zachariason, Rob (2012). Electrical materials. Clifton Park, N.Y.: Delmar, Cengage Learning. p. 90. ISBN 978-1111640064.
^ "2 Inch Chase Nipple, Malleable Iron with Dura Plate Finish for Use with Rigid/IMC Conduit". Thomas & Betts Corporation. 2018. Archived from the original on May 21, 2018.
^ William Dixon Weaver; Jonathan E. Woodbridge; Cecil Percy Poole, eds. (1900). American Electrician. Vol. 12. Princeton University. p. 550.

External links

Chase Nipple : Bushed Nipple. Electricians Library. Archived from the original on 2021-12-21 – via YouTube". Shows a 2-inch chase nipple.{{cite AV media}}: CS1 maint: postscript (link)

[1] Zachariason, Rob (2012). Electrical materials. Clifton Park, N.Y.: Delmar, Cengage Learning. p. 90. ISBN 978-1111640064.

[2] "2 Inch Chase Nipple, Malleable Iron with Dura Plate Finish for Use with Rigid/IMC Conduit". Thomas & Betts Corporation. 2018. Archived from the original on May 21, 2018.

[3] William Dixon Weaver; Jonathan E. Woodbridge; Cecil Percy Poole, eds. (1900). American Electrician. Vol. 12. Princeton University. p. 550.

[1]

[2]

[3]

v t e Plumbing
Fundamental concepts	Air gap (plumbing) Backflow Compatibility (chemical) Corrosion Drain (plumbing) Drinking water Fuel gas Friction loss Grade (slope) Greywater Heat trap Hydrostatic loop Leak Neutral axis Onsite sewage facility Pressure Sanitary sewer Sewer gas Sewage Sewerage Siphon Storm sewer Stormwater Surface tension Tap water Thermal expansion Thermal insulation Thermosiphon Trap (plumbing) Venturi effect Wastewater Water hammer Water supply network Water table Well
Technology	Brazing British Standard Pipe (BSP) Cast iron pipe Chemical drain cleaners Compression fitting Copper tubing Crimp (joining) Drain-waste-vent system Ductile iron pipe Flare fitting Garden Hose Thread (GHT) Gasket Hydronics Leak detection National Pipe Thread (NPT) Nominal Pipe Size (NPS) O-ring Oakum Pipe (fluid conveyance) Pipe dope Pipe support Plastic pipework Push-to-pull compression fittings Putty Sealant Sewage pumping Soldering Solvent welding Swaging Thread seal tape Threaded pipe Tube bending Water heat recycling
Components	Atmospheric vacuum breaker Automatic bleeding valve Automatic faucet Backflow prevention device Ball valve Bleed screw Booster pump Butterfly valve Check valve Chemigation valve Chopper pump Circulator pump Cistern Closet flange Concentric reducer Condensate pump Coupling (piping) Diaphragm valve Dielectric union Double check valve Eccentric reducer Expansion tank Faucet aerator Float switch Float valve Floor drain Flow limiter Flushing trough Flushometer Gate valve Globe valve Grease trap Grinder pump Hose coupling Manifold Needle valve Nipple (plumbing) Pinch valve Piping and plumbing fitting Plug (sanitation) Pressure regulator Pressure vacuum breaker Pressure-balanced valve Pump Radiator (heating) Reduced pressure zone device Reducer Relief valve Riser clamp Rooftop water tower Safety valve Sewage pump Street elbow Submersible pump Tap (valve) Thermostatic mixing valve Trench drain Vacuum breaker Vacuum ejector Valve Water tank Zone valve
Plumbing fixtures	Accessible bathtub Bathtub Bidet Dehumidifier Dishwasher Drinking fountain Electric water boiler Evaporative cooler Flush toilet Garbage disposal unit Hot water storage tank Humidifier Icemaker Instant hot water dispenser Laundry tub Shower water recycling shower Sink Storage water heater Sump pump Tankless water heater Urinal Washing machine Washlet Water dispenser Water filter Water heater Water softener
Specialized tools	Basin wrench Blowtorch Borescope Core drill Drain cleaner Driving cap Flare-nut wrench Pipecutter Pipe wrench Plumber's snake Plumber wrench Plunger Strap wrench Tap and die
Measurement and control	Control valve Flow sensor Pressure sensor Water detector Water metering
Professions, trades, and services	Hydronic balancing Hydrostatic testing Leak detection Mechanical, electrical, and plumbing Pipe marking Pipefitter Pipelayer Plumber
Industry organizations and standards	International Association of Plumbing and Mechanical Officials (IAPMO) NSF International Plumbing & Drainage Institute (PDI) Uniform Plumbing Code (UPC) World Plumbing Council (WPC)
Health and safety	Plumbing code Scalding Waterborne disease
See also	Fire sprinkler system Piping Template:HVAC Template:Public health Template:Sewerage Template:Toilets Template:Wastewater

Chase nipple

See also

References

Further reading

External links