Jump to content

United States Naval Construction Battalion flame thrower tanks

From Wikipedia, the free encyclopedia
(Redirected from Flame throwing Seabees)
Marines use a "Satan" to incinerate a Japanese pillbox on Saipan.
The CB-H2 flamethrower seen here on Iwo Jima had a range of 150 yards[1]
117th CB logo[2]
The Seabees' training model of a coaxial H1a-H5a flamethrower shown by Col Unmacht's staff to visitors would not see combat until Korea
Night demonstration at Schofield Barracks 3 weeks prior to Iwo Jima.

During WWII United States Naval Construction Battalions ("Seabees") modified/created all of the main armament flame throwing tanks that were used in the Pacific War: by USMC in the Battle of Saipan, Battle of Tinian, Battle of Iwo Jima, and by the U.S. Army in the Battle of Okinawa.

They were a weapon Japanese troops feared and the Marine Corps said was the best weapon they had in the taking of Iwo Jima.[3] After Okinawa the Army stated that the tanks had a psychological presence on the battlefield. U.S. troops preferred to follow them over standard armor for the fear they put in the enemy.[4]

Pacific field commanders had tried field modified mechanized flame throwers early on,[5] with the Marine Corps deciding to leave further development to the Army. The Navy had an interest in flame throwing and five Navy Mark I flamethrowers arrived in Hawaii in April 1944. The Navy deemed them "unsuitable" due to their weight and turned the over to the Army's Chemical Warfare Service.[6] In May a top secret composite unit was assembled at Schofield Barracks.[7] It was led by Colonel Unmacht of the US Army Chemical Warfare Service, Central Pacific Area (CENPAC)[4][8] Col. Unmacht began the project with only the 43rd Chemical Laboratory Company. They modified the first light tank designating it a "Satan". The flame tank group was expanded with men from the 5th Marine tank battalion and 25 from the 117th CB.[7] The newly attached Seabees went over what the Army had created and concluded it was a little over engineered. They recommended reducing the number of moving parts from over a hundred to a half dozen.

V Amphibious Corps (VAC) wanted mechanized flamethrowing capabilities for the Marianas operations. VAC had ordered and received two shipments of Canadian Ronson F.U.L. Mk IV flamethrowers (30 flamethrowers in total) to field modify tanks. With a war to wage field modification was much quicker than going through official military procurement channels. The 117th CB was assigned to the upcoming Saipan operation. Col Unmacht worked out an arrangement to not only keep the 117th Seabees he had, but get more. Augmented by the additional Seabees, the group worked sun up to sundown and, with Seabee can-do twenty-four M3s were modified to start the campaign.[8] The very first, made by the 43rd Co, was christened "Hells Afire".[9] The installation configuration of the flamethrower components limited the turret's traverse to 180°. As Satans were produced Colonel Unmacht had the Seabees conduct a comprehensive series of 40-hour classes on flame tank operation with first and second eschelon maintenance. First, for officers and enlisted of the Marine Corps and then later for the Army.[10][8] The Satans had a range of 40–80 yd (37–73 m) and were the first tanks to have the main armament swapped for flame throwers. They were divided between the 2nd and 4th Marine Divisions for Siapan and Tinian with Tinian being more favorable to their use.[8]

  • Four Seabees received Navy/Marine Corps commendations for their work from Lt. Gen. Holland M. Smith Commanding General(USMC) FMF Pacific.[7]
  • At least 7 were awarded the Bronze Star.[9]

Mid-September the Army decided to officially form a CWS "Flame Thrower Group" with Col Unmacht requesting 56 additional Seabees.[9] The group included more Army CWS and 81st Ordnance men as well.[7] It was apparent that a larger flamethrower on a bigger tank would be more desirable, but very few tanks were available for conversion. Operation Detachment was next and Col Unmacht's group located eight M4A3 Sherman medium tanks for it. The Seabees worked to combine the best elements from three different flame units: the Ronson, the Navy model I and those Navy Mk-1s the Navy gave up.[7] MMS1c A.A. Reiche and EM2c Joseph Kissel are credited with designing the CB-H1. Installation required 150 lbs of welding rod, 1100 electrical connections, and cost between $20,000-25,000 per tank[7](adj. for inflation $288,000-$360,000 in 2019). The CB-H1 flamethrower operated on 300 psi which gave it a range of 400 ft (120 m) and could transverse 270°.[7] This model was quickly superseded by the CB-H2 which was far better.[11] EM2c Kissel and SF1c J.T. Patterson accompanied the tanks to oversee maintenance during the battle of Iwo Jima. Kissel filled in as an assistant driver/gunner with tank crews on 20 days of the operation.[9]

In November 1944, prior to the rave USMC reviews of Iwo Jima, the Fleet Marine Force had requested 54 mechanized flame throwers, nine for each of the Marine Corps divisions[12] On Iwo the tanks all landed D-day and went into action on D+2, sparingly at first. As the battle progressed, portable flame units sustained casualty rates up to 92%, leaving few troops trained to use the weapon. More and more calls came for the Mark-1s to the point that the Marines became dependent upon the tanks and would hold up their assault until a flame tank was available.[4] Since each tank battalion had only four they were not assigned. Rather, they were "pooled" and would dispatch from their respective refueling locations as the battle progressed. One the 4th Division tanks had a 50 cal. machine gun coaxial to the flamethrower as well as 4 in (100 mm) concrete armor to counter placement of magnetic charges. Towards the end of the battle, 5th Marine tanks used between 5,000 to 10,000 US gal (19,000 to 38,000 L) gallons per day.[4]

For Okinawa the 10th Army decided that the entire 713th Tank Battalion would provisionally convert to flame. The battalion was tasked to support both the Army and the Marine Corps assault. It was ordered to Schofield Barracks on Nov 10. There the Seabees supervised three officers and 60 enlisted of the 713th convert all 54 of their tanks to Ronsons.[12][13] The Ronsons did not have the range of either the CB-H1 or CB-H2.

In June 1945, the 43rd Chemical Lab. Co. had developed a stabilized flamethrower fuel (napalm). They oversaw CB construction of an activating plant that produced over 250,000 gallons.[9] The 713th went through 200,000 gallons on Okinawa. Also in June, the Army cancelled all further production orders for any more M4 Shermans. This caused Under Secretary of War Robert Patterson to place an expedite on Col. Unmacht's production of flame tanks. They were given a "Triple A" procurement priority, the same given to the B-29 and the Atomic bomb projects.[14]

Another 72 tanks were ordered by the Marine Corps for the planned invasion of Japan[4] of which Col. Unmacht's crews had 70 ready by Victory over Japan Day. In total Unmacht's Flame Tank Group produced 354 tanks.[15]

Cross section through a CB-H1 flame thrower

The military did not have uniform terminology for referencing mechanized flamethrowers so there is some wording variation in documents. The Seabees produced 11 different models of flame throwing tanks off three basic variations identified with a POA-CWS-H number[9]

"Primary" where the main armament was removed and replaced.

  • The first eight had Navy CB-H1 or CB-H2 flamethrowers. US Army Chemical Corps variously identified these tanks as POA-CWS-H1,[9] (Pacific Ocean Area-Chemical Warfare Section-Hawaii) CWS-POA-H2, CWS-POA-H1 H2, OR CWS-"75"-H1 H2 mechanized flamethrowers. US Marine and US Army observer documents from Iwo Jima refer to them as the CB-Mk-1 or CB-H1.[16] Marines on the lines simply called them the Mark I.[16] The official USMC designation was "M4 A3R5".[16] The Japanese referred to them as M1 tanks and it is speculated that they did so due to a poor translation of "MH-1".[16]
  • The next 54 tanks had Ronson flamethrowers. That made them the third tank variant produced. Army records identify them as POA-CWS-H1s.
  • Some of these tanks were configured with an external 400-foot (120 m) long hose supplying a M2-2 portable flamethrower that ground troops could use.[16] This variation could throw some 60 ft (18 m). A drawback to this attachment was all the fuel it took to charge the hose line so it could fire diminished the tank's overall effectiveness. Army documents post-war refer to this variation as being a CWS-POA-H1.[16]

"Auxiliary" where the flame thrower was mounted coaxial to the main armament. Eighteen of the first generation model were on the way to the 10th Army on Okinawa, but the island was taken before they arrived, so they were given to the 3rd Marine Division tank battalion on Guam.[17]

  • 75mm main armament with Ronson
  • 75mm main armament H1a-H5a
  • 105mm main armament with Ronson
  • 105mm main armament with H1a-H5a USMC designation M4-A3E8. These would be at Inchon in 1950.[16]

In mid-1945 the Seabees started producing the second generation of these tanks. These H1a-H5a Shermans, with either 75mm or 105mm main armaments, were jointly referred to as CWS-POA-5s.

"Periscope Mount" This model was based upon work done by the U.S. Army at Fort Knox. The flame thrower was mounted through the assistant driver's hatch alongside their tank periscope which meant that the bow machine gun could be retained. 176 were produced.[18] Word spread that one of these tanks lost a crew when the flamethrower nozzle took a hit.[8] The Marine Corps did not want this design.[18]

  • H1 periscope[18]
  • H1A periscope[18]
  • H1B periscope[18]
  • Examples labeled POA-CWS-H1 and POA-CWS-H5 are on display at the Mahaffey Museum at Fort Leonard Wood Missouri.[9]
  • 5th Marine CB-H1 in action on D+22,[19]
  • Example M42 B1E9 [10]

The Marines preferred the CB tanks to any produced in the U.S. at that time.[20] The Marine Corps and Army both felt that the flame throwing tanks saved U.S. troops lives and kept the casualty numbers lower than they would have been had the tanks not been used.[8] They also agreed that they would need many for the invasion of the Japanese homeland.

Postwar the Army stood down the provisional 713th keeping no flame tanks.[16] The Marine Corps came close to doing the same. When the Korean War broke out they were able to put together nine CWS-POA-H5s from Pendelton and Hawaii. Together they formed a platoon, named the "Flame Dragons", in the 1st tank battalion.[21] They landed at Inchon in 1950 and were the only U.S. mechanized flame unit to be in Korea.[21]

  • Col. Unmacht 1946 Military Review flame tank article.[22]

References

[edit]
  1. ^ LVT4 Landing Vehicle, Tracked, Unarmored (Mark IV), John Pike, GlobalSecurity.Org, July 2011, paragraph 5[LVT4 Landing Vehicle, Tracked, Unarmored (Mark IV)]
  2. ^ 117th Naval Construction Battalion Cruisebook, NHHC, Seabee Museum website, Port Hueneme CA, Jan. 2020, p. 22,23 [1]
  3. ^ Chapter: the Bitter End, CLOSING IN: Marines in the Seizure of Iwo Jima, Colonel Joseph H. Alexander, USMC (Ret), History and Museums Division, Headquarters, U.S. Marine Corps, Washington, D.C., 1994, p.37 [2]
  4. ^ a b c d e Kelber, Brookes E.; Birdsell, Dale (1990), "Chapter XV, The Flame Thrower in the Pacific: Marianas to Okinawa" (PDF), United States Army in World War II, The Technical Services, The Chemical Warfare Service; Chemicals in Combat, Center of Military History United States Army, Washington DC, pp. 558–583, 586
  5. ^ Kelber and Birdsall (1966) p 558
  6. ^ Armored Thunderbolt: The U.S. Sherman in World War II, Steve Zaloga, 2008
  7. ^ a b c d e f g "New Tanks for Old", U.S. Navy Civil popEngineer Corps Bulletin, vol. 2 NAVDOCKS P-2, no. 14, Bureau of BuDocks, Dept. of the Navy, p. 51 on line 21, January 1948
  8. ^ a b c d e f CHAPTER XV, The Flame Thrower in the Pacific: Marianas to Okinawa, WWII Chemical in Combat, Dec 2001, p. 558 [3]
  9. ^ a b c d e f g Unmacht (CWS), Col Geo. F. (April 1948), "Flame Throwing Seabees", United States Naval Institute Proceedings, vol. 74, no. 342, pp. 425–7
  10. ^ Dr. Frank A. Blazich Jr., This week in Seabee History (Week of Oct. 23), U.S. Navy Seabee Museum, Port Hueneme, CA.
  11. ^ New Tanks for Old, USN CEC Bulletin Vol. 1, No. 1, Dec. 1946, BuDocks Navy Deot, U.S. GPO, Washington D.C., p. 53. [4]
  12. ^ a b Zaloga 2013, p. 29.
  13. ^ 1st Lt. Patrick J. Donahoe (1994), "Flamethrower Tanks on Okinawa", Armor, no. Jan-Feb 1994, U.S. Army Armor Center, Fort Knox, p. 6{{citation}}: CS1 maint: numeric names: authors list (link)
  14. ^ History Friday: Mechanized Flame Weapons from the invasion That Never Happened, Chicagoboyz Blog archive, Trent Telenko, Nov 2013, chicagoboyz.net [5]
  15. ^ Montcastle, John W. (2016), Flame On, U.S. Incendiary Weapons, 1918-1945, StackpoleBooks, Mechanicsburg, PA., p. 142 #33, ISBN 9780811764919
  16. ^ a b c d e f g h Telenko, Trent (August 30, 2013), "History Friday: Technological Surprise & the Defeat of the 193rd Tank Battalion at Kakuza Ridge", Chicago Boyz Blog archive
  17. ^ The Chemical Warfare Service: From the Laboratory to the Field, L.B. Brophy, W.D. Miled, R.C. Cochrane, of Military History, U.S. Army, Washington D.C., U.S. GPO, Washington D.C., 1959, p. 153 [6]
  18. ^ a b c d e Zaloga, Steven J. (2013), US Flamethrower Tanks of World War II, Bloomsbury, ISBN 9781780960272
  19. ^ "New Footage: Flame Tanks on Iwo Jima (Silent)", Marine Corps Film Archive – via youtube
  20. ^ "Commandant USMC Memorandum for the record: 22 Jan, 1945, RG 127, File #2000,NA"
  21. ^ a b Now They're Flame Dragons, chapt 50, Flame Dragons of the Korean War, Jerry Ravin & Jack Carty, Turner Publishing, 412 Broadway, Paducah, KY, 2003, p.222 [7]
  22. ^ Flamethrower Tanks in the Pacific Ocean Areas, Colonel George F. Unmacht, Chemical Warfare Service Chemical Officer. United States Army, Forces. Middle Pacific, Military Review, March 1946, Vol 25 No 12, p. 44-51, Combined Arms Research Library, created 2010-09-10, [8]