Cleopatra (cylinder ship)
 Cleopatra in the River Thames
| |
| History | |
|---|---|
| Name | Cleopatra |
| Builder | Thames Ironworks |
| Launched | 1877 |
| Out of service | 1878 |
| General characteristics | |
| Length | 92 ft (28 m) |
| Beam | 16 ft (4.9 m) |
Cleopatra was a "cylinder ship" built to take Cleopatra's Needle from Alexandria to London in 1877.
The obelisk weighed more than 200 tons. It was encased in a cylindrical iron pontoon which was then rolled by means of levers and chains down a track into the sea. The pontoon was fitted with a deck-house, mast, rudder and steering gear and was crewed by Maltese sailors. The pontoon was towed to Great Britain by the steamship Olga leaving on 21 September 1877. Captain Henry Carter supervised Cleopatra's building and became her commander. Captain Booth commanded Olga.
On 14 October 1877 the Cleopatra was in danger of sinking off France in the Bay of Biscay. The steam-ship towing her, the Olga, sent six volunteers in a boat to take off the Cleopatra's crew, but the boat swamped and the volunteers drowned. Eventually the Olga managed to draw alongside and rescue Cleopatra's crew of five and skipper, they cut the towrope, and left the vessel adrift in the Bay. Five days later a ship spotted the ‘Cleopatra’ floating undamaged off the northern coast of Spain, and she was towed to the Ferrol, Galicia. There a steam-ship, the Anglia, arrived to tow her to London. They arrived at Gravesend on 21 January 1878.[1] Cleopatra was broken up immediately after the obelisk had been removed on 6 July 1878. The needle was installed on the Thames Embankment in September 1878, where it still stands.[1]
Design
[edit]Designed by engineer John Dixon, Cleopatra was essentially an iron cylinder[2] 92 ft (28 m) long and 16 ft (4.9 m) diameter containing the obelisk. It was supplemented by a bow and a vertical stern, rudder, two sidewalls, and a mast for sails to stabilise the vessel. A bridge was built to accommodate the crew.
Designed as a pontoon, and commanded by Captain Carter, she was to be towed to London by the ship Olga, commanded by Captain Booth.
The cylindrical shape was a clever choice in the context of a constrained budget (private funding by some patrons). Indeed, the cylinder, made of sheet metal riveted curves was literally built around the obelisk, with circular internal partitions used as cradles for the monolith.
Both ends were topped with a crown of planks, the cylinder could ride on the Nile, with minimal effort, using cables driven by winches. Unfortunately, at the time of launching, a concealed rock in the mud punctured the cylinder which then blocked the waterway.
After towing to a dry-dock of the Egyptian Admiralty, the cylinder was turned into a ship by adding an internal ballast made of rails, a bow and a stern with rudder and a roof to shelter the crew. It carried a single mast rigged with gaff and foresail.[3]
Once completed, the ship looked like a primitive submarine, but its seagoing capabilities were more limited and in retrospect, the choice of crossing the Bay of Biscay in the autumn was a risky choice.
See also
[edit]- Cleopatra's Needle (London), moving it
- SS Dessoug, the ship used to take the other Cleopatra's Needle to New York
- Cleopatra's Needle (New York)
Notes
[edit]- ^ a b "Cleopatra's needle being brought to England, 1877". Royal Museums Greenwich. Retrieved 14 August 2018. Content is copied from this source, which is protected by Crown copyright. Reuse is authorised, provided the source is acknowledged.
- ^ "Cleopatra's Needle". Thames Tugs.
- ^ "Barge Cleopatra, Britain, 1878".
References
[edit]- Brier, Bob (21 April 2016). Cleopatra's Needles: The Lost Obelisks of Egypt. Bloomsbury Academic. ISBN 9781474242936.
- "Cleopatra". Shipping and Shipbuilding. Shipping and Shipbuilding Research Trust.
- The Builder. 1 January 1877.
- Mason, J (1 January 1877). The Annual summary.
- Wilson, Sir Erasmus (1 January 1877). Cleopatra's Needle: With Brief Notes on Egypt and Egyptian Obelisks. Brain & Company.
