Jump to content

Semiconductor device

From Wikipedia, the free encyclopedia
(Redirected from Semiconductor electronics)
For information on semiconductor physics, see Semiconductor.
Outlines of some packaged semiconductor devices

A semiconductor device is an electronic component that relies on the electronic properties of a semiconductor material (primarily silicon, germanium, and gallium arsenide, as well as organic semiconductors) for its function. Its conductivity lies between conductors and insulators. Semiconductor devices have replaced vacuum tubes in most applications. They conduct electric current in the solid state, rather than as free electrons across a vacuum (typically liberated by thermionic emission) or as free electrons and ions through an ionized gas.

Semiconductor devices are manufactured both as single discrete devices and as integrated circuits, which consist of two or more devices—which can number from the hundreds to the billions—manufactured and interconnected on a single semiconductor wafer (also called a substrate).

Semiconductor materials are useful because their behavior can be easily manipulated by the deliberate addition of impurities, known as doping. Semiconductor conductivity can be controlled by the introduction of an electric or magnetic field, by exposure to light or heat, or by the mechanical deformation of a doped monocrystalline silicon grid; thus, semiconductors can make excellent sensors. Current conduction in a semiconductor occurs due to mobile or "free" electrons and electron holes, collectively known as charge carriers. Doping a semiconductor with a small proportion of an atomic impurity, such as phosphorus or boron, greatly increases the number of free electrons or holes within the semiconductor. When a doped semiconductor contains excess holes, it is called a p-type semiconductor (p for positive electric charge); when it contains excess free electrons, it is called an n-type semiconductor (n for a negative electric charge). A majority of mobile charge carriers have negative charges. The manufacture of semiconductors controls precisely the location and concentration of p- and n-type dopants. The connection of n-type and p-type semiconductors form p–n junctions.

The most common semiconductor device in the world is the MOSFET (metal–oxide–semiconductor field-effect transistor),[1] also called the MOS transistor. As of 2013, billions of MOS transistors are manufactured every day.[2] Semiconductor devices made per year have been growing by 9.1% on average since 1978, and shipments in 2018 are predicted for the first time to exceed 1 trillion,[3] meaning that well over 7 trillion have been made to date.

Main types

[edit]

Diode

[edit]
Main article: Diode

A semiconductor diode is a device typically made from a single p–n junction. At the junction of a p-type and an n-type semiconductor, there forms a depletion region where current conduction is inhibited by the lack of mobile charge carriers. When the device is forward biased (connected with the p-side, having a higher electric potential than the n-side), this depletion region is diminished, allowing for significant conduction. Contrariwise, only a very small current can be achieved when the diode is reverse biased (connected with the n-side at lower electric potential than the p-side, and thus the depletion region expanded).

Exposing a semiconductor to light can generate electron–hole pairs, which increases the number of free carriers and thereby the conductivity. Diodes optimized to take advantage of this phenomenon are known as photodiodes. Compound semiconductor diodes can also produce light, as in light-emitting diodes and laser diode

Transistor

[edit]
Main article: Transistor

Bipolar junction transistor

[edit]
An n–p–n bipolar junction transistor structure

Bipolar junction transistors (BJTs) are formed from two p–n junctions, in either n–p–n or p–n–p configuration. The middle, or base, the region between the junctions is typically very narrow. The other regions, and their associated terminals, are known as the emitter and the collector. A small current injected through the junction between the base and the emitter changes the properties of the base-collector junction so that it can conduct current even though it is reverse biased. This creates a much larger current between the collector and emitter, controlled by the base-emitter current.

Field-effect transistor

[edit]
Main article: Field-effect transistor

Another type of transistor, the field-effect transistor (FET), operates on the principle that semiconductor conductivity can be increased or decreased by the presence of an electric field. An electric field can increase the number of free electrons and holes in a semiconductor, thereby changing its conductivity. The field may be applied by a reverse-biased p–n junction, forming a junction field-effect transistor (JFET) or by an electrode insulated from the bulk material by an oxide layer, forming a metal–oxide–semiconductor field-effect transistor (MOSFET).

Metal-oxide-semiconductor

[edit]
Main article: MOSFET
See also: List of semiconductor scale examples and Transistor count
Operation of a MOSFET and its Id-Vg curve. At first, when no gate voltage is applied. There is no inversion electron in the channel, the device is OFF. As gate voltage increase, the inversion electron density in the channel increase, the current increases, and the device turns on.

The metal-oxide-semiconductor FET (MOSFET, or MOS transistor), a solid-state device, is by far the most used widely semiconductor device today. It accounts for at least 99.9% of all transistors, and there have been an estimated 13 sextillion MOSFETs manufactured between 1960 and 2018.[4]

The gate electrode is charged to produce an electric field that controls the conductivity of a "channel" between two terminals, called the source and drain. Depending on the type of carrier in the channel, the device may be an n-channel (for electrons) or a p-channel (for holes) MOSFET. Although the MOSFET is named in part for its "metal" gate, in modern devices polysilicon is typically used instead.

Other types

[edit]
See also: Electronic component § Semiconductors

Two-terminal devices:

Three-terminal devices:

Four-terminal devices:

Materials

[edit]
Main article: Semiconductor materials

By far, silicon (Si) is the most widely used material in semiconductor devices. Its combination of low raw material cost, relatively simple processing, and a useful temperature range makes it currently the best compromise among the various competing materials. Silicon used in semiconductor device manufacturing is currently fabricated into boules that are large enough in diameter to allow the production of 300 mm (12 in.) wafers.

Germanium (Ge) was a widely used early semiconductor material but its thermal sensitivity makes it less useful than silicon. Today, germanium is often alloyed with silicon for use in very-high-speed SiGe devices; IBM is a major producer of such devices.

Gallium arsenide (GaAs) is also widely used in high-speed devices but so far, it has been difficult to form large-diameter boules of this material, limiting the wafer diameter to sizes significantly smaller than silicon wafers thus making mass production of GaAs devices significantly more expensive than silicon.

Gallium Nitride (GaN) is gaining popularity in high-power applications including power ICs, light-emitting diodes (LEDs), and RF components due to its high strength and thermal conductivity. Compared to silicon, GaN's band gap is more than 3 times wider at 3.4 eV and it conducts electrons 1,000 times more efficiently.[5][6]

Other less common materials are also in use or under investigation.

Silicon carbide (SiC) is also gaining popularity in power ICs and has found some application as the raw material for blue LEDs and is being investigated for use in semiconductor devices that could withstand very high operating temperatures and environments with the presence of significant levels of ionizing radiation. IMPATT diodes have also been fabricated from SiC.

Various indium compounds (indium arsenide, indium antimonide, and indium phosphide) are also being used in LEDs and solid-state laser diodes. Selenium sulfide is being studied in the manufacture of photovoltaic solar cells.

The most common use for organic semiconductors is organic light-emitting diodes.

Applications

[edit]

All transistor types can be used as the building blocks of logic gates, which are fundamental in the design of digital circuits. In digital circuits like microprocessors, transistors act as on-off switches; in the MOSFET, for instance, the voltage applied to the gate determines whether the switch is on or off.

Transistors used for analog circuits do not act as on-off switches; rather, they respond to a continuous range of inputs with a continuous range of outputs. Common analog circuits include amplifiers and oscillators.

Circuits that interface or translate between digital circuits and analog circuits are known as mixed-signal circuits.

Power semiconductor devices are discrete devices or integrated circuits intended for high current or high voltage applications. Power integrated circuits combine IC technology with power semiconductor technology, these are sometimes referred to as "smart" power devices. Several companies specialize in manufacturing power semiconductors.

Component identifiers

[edit]

The part numbers of semiconductor devices are often manufacturer specific. Nevertheless, there have been attempts at creating standards for type codes, and a subset of devices follow those. For discrete devices, for example, there are three standards: JEDEC JESD370B in the United States, Pro Electron in Europe, and Japanese Industrial Standards (JIS).

Fabrication

[edit]
This section is an excerpt from Semiconductor device fabrication.[edit]
NASA's Glenn Research Center clean room

Semiconductor device fabrication is the process used to manufacture semiconductor devices, typically integrated circuits (ICs) such as computer processors, microcontrollers, and memory chips (such as RAM and Flash memory). It is a multiple-step photolithographic and physico-chemical process (with steps such as thermal oxidation, thin-film deposition, ion-implantation, etching) during which electronic circuits are gradually created on a wafer, typically made of pure single-crystal semiconducting material. Silicon is almost always used, but various compound semiconductors are used for specialized applications.

The fabrication process is performed in highly specialized semiconductor fabrication plants, also called foundries or "fabs",[7] with the central part being the "clean room". In more advanced semiconductor devices, such as modern 14/10/7 nm nodes, fabrication can take up to 15 weeks, with 11–13 weeks being the industry average.[8] Production in advanced fabrication facilities is completely automated, with automated material handling systems taking care of the transport of wafers from machine to machine.[9]

A wafer often has several integrated circuits which are called dies as they are pieces diced from a single wafer. Individual dies are separated from a finished wafer in a process called die singulation, also called wafer dicing. The dies can then undergo further assembly and packaging.[10]

Within fabrication plants, the wafers are transported inside special sealed plastic boxes called FOUPs.[9] FOUPs in many fabs contain an internal nitrogen atmosphere[11][12] which helps prevent copper from oxidizing on the wafers. Copper is used in modern semiconductors for wiring.[13] The insides of the processing equipment and FOUPs is kept cleaner than the surrounding air in the cleanroom. This internal atmosphere is known as a mini-environment and helps improve yield which is the amount of working devices on a wafer. This mini environment is within an EFEM (equipment front end module)[14] which allows a machine to receive FOUPs, and introduces wafers from the FOUPs into the machine. Additionally many machines also handle wafers in clean nitrogen or vacuum environments to reduce contamination and improve process control.[9] Fabrication plants need large amounts of liquid nitrogen to maintain the atmosphere inside production machinery and FOUPs, which are constantly purged with nitrogen.[11][12] There can also be an air curtain or a mesh[15] between the FOUP and the EFEM which helps reduce the amount of humidity that enters the FOUP and improves yield.[16][17]

Companies that manufacture machines used in the industrial semiconductor fabrication process include ASML, Applied Materials, Tokyo Electron and Lam Research.

History of development

[edit]
Further information: History of electrical engineering

Cat's-whisker detector

[edit]
Main article: Cat's-whisker detector

Semiconductors had been used in the electronics field for some time before the invention of the transistor. Around the turn of the 20th century they were quite common as detectors in radios, used in a device called a "cat's whisker" developed by Jagadish Chandra Bose and others. These detectors were somewhat troublesome, however, requiring the operator to move a small tungsten filament (the whisker) around the surface of a galena (lead sulfide) or carborundum (silicon carbide) crystal until it suddenly started working.[18] Then, over a period of a few hours or days, the cat's whisker would slowly stop working and the process would have to be repeated. At the time their operation was completely mysterious. After the introduction of the more reliable and amplified vacuum tube based radios, the cat's whisker systems quickly disappeared. The "cat's whisker" is a primitive example of a special type of diode still popular today, called a Schottky diode.

Metal rectifier

[edit]
Main article: Metal rectifier

Another early type of semiconductor device is the metal rectifier in which the semiconductor is copper oxide or selenium. Westinghouse Electric (1886) was a major manufacturer of these rectifiers.

World War II

[edit]

During World War II, radar research quickly pushed radar receivers to operate at ever higher frequencies about 4000 MHz and the traditional tube-based radio receivers no longer worked well. The introduction of the cavity magnetron from Britain to the United States in 1940 during the Tizard Mission resulted in a pressing need for a practical high-frequency amplifier.[citation needed]

On a whim, Russell Ohl of Bell Laboratories decided to try a cat's whisker. By this point, they had not been in use for a number of years, and no one at the labs had one. After hunting one down at a used radio store in Manhattan, he found that it worked much better than tube-based systems.

Ohl investigated why the cat's whisker functioned so well. He spent most of 1939 trying to grow more pure versions of the crystals. He soon found that with higher-quality crystals their finicky behavior went away, but so did their ability to operate as a radio detector. One day he found one of his purest crystals nevertheless worked well, and it had a clearly visible crack near the middle. However, as he moved about the room trying to test it, the detector would mysteriously work, and then stop again. After some study he found that the behavior was controlled by the light in the room – more light caused more conductance in the crystal. He invited several other people to see this crystal, and Walter Brattain immediately realized there was some sort of junction at the crack.

Further research cleared up the remaining mystery. The crystal had cracked because either side contained very slightly different amounts of the impurities Ohl could not remove – about 0.2%. One side of the crystal had impurities that added extra electrons (the carriers of electric current) and made it a "conductor". The other had impurities that wanted to bind to these electrons, making it (what he called) an "insulator". Because the two parts of the crystal were in contact with each other, the electrons could be pushed out of the conductive side which had extra electrons (soon to be known as the emitter), and replaced by new ones being provided (from a battery, for instance) where they would flow into the insulating portion and be collected by the whisker filament (named the collector). However, when the voltage was reversed the electrons being pushed into the collector would quickly fill up the "holes" (the electron-needy impurities), and conduction would stop almost instantly. This junction of the two crystals (or parts of one crystal) created a solid-state diode, and the concept soon became known as semiconduction. The mechanism of action when the diode off has to do with the separation of charge carriers around the junction. This is called a "depletion region".

Development of the diode

[edit]

Armed with the knowledge of how these new diodes worked, a vigorous effort began to learn how to build them on demand. Teams at Purdue University, Bell Labs, MIT, and the University of Chicago all joined forces to build better crystals. Within a year germanium production had been perfected to the point where military-grade diodes were being used in most radar sets.

Development of the transistor

[edit]
Main article: History of the transistor

After the war, William Shockley decided to attempt the building of a triode-like semiconductor device. He secured funding and lab space, and went to work on the problem with Brattain and John Bardeen.

The key to the development of the transistor was the further understanding of the process of the electron mobility in a semiconductor. It was realized that if there were some way to control the flow of the electrons from the emitter to the collector of this newly discovered diode, an amplifier could be built. For instance, if contacts are placed on both sides of a single type of crystal, current will not flow between them through the crystal. However, if a third contact could then "inject" electrons or holes into the material, the current would flow.

Actually doing this appeared to be very difficult. If the crystal were of any reasonable size, the number of electrons (or holes) required to be injected would have to be very large, making it less than useful as an amplifier because it would require a large injection current to start with. That said, the whole idea of the crystal diode was that the crystal itself could provide the electrons over a very small distance, the depletion region. The key appeared to be to place the input and output contacts very close together on the surface of the crystal on either side of this region.

Brattain started working on building such a device, and tantalizing hints of amplification continued to appear as the team worked on the problem. Sometimes the system would work but then stop working unexpectedly. In one instance a non-working system started working when placed in water. Ohl and Brattain eventually developed a new branch of quantum mechanics, which became known as surface physics, to account for the behavior. The electrons in any one piece of the crystal would migrate about due to nearby charges. Electrons in the emitters, or the "holes" in the collectors, would cluster at the surface of the crystal where they could find their opposite charge "floating around" in the air (or water). Yet they could be pushed away from the surface with the application of a small amount of charge from any other location on the crystal. Instead of needing a large supply of injected electrons, a very small number in the right place on the crystal would accomplish the same thing.

Their understanding solved the problem of needing a very small control area to some degree. Instead of needing two separate semiconductors connected by a common, but tiny, region, a single larger surface would serve. The electron-emitting and collecting leads would both be placed very close together on the top, with the control lead placed on the base of the crystal. When current flowed through this "base" lead, the electrons or holes would be pushed out, across the block of the semiconductor, and collect on the far surface. As long as the emitter and collector were very close together, this should allow enough electrons or holes between them to allow conduction to start.

First transistor

[edit]
A stylized replica of the first transistor

The Bell team made many attempts to build such a system with various tools but generally failed. Setups, where the contacts were close enough, were invariably as fragile as the original cat's whisker detectors had been, and would work briefly, if at all. Eventually, they had a practical breakthrough. A piece of gold foil was glued to the edge of a plastic wedge, and then the foil was sliced with a razor at the tip of the triangle. The result was two very closely spaced contacts of gold. When the wedge was pushed down onto the surface of a crystal and voltage was applied to the other side (on the base of the crystal), current started to flow from one contact to the other as the base voltage pushed the electrons away from the base towards the other side near the contacts. The point-contact transistor had been invented.

While the device was constructed a week earlier, Brattain's notes describe the first demonstration to higher-ups at Bell Labs on the afternoon of 23 December 1947, often given as the birthdate of the transistor. What is now known as the "p–n–p point-contact germanium transistor" operated as a speech amplifier with a power gain of 18 in that trial. John Bardeen, Walter Houser Brattain, and William Bradford Shockley were awarded the 1956 Nobel Prize in physics for their work.

Etymology of "transistor"

[edit]

Bell Telephone Laboratories needed a generic name for their new invention: "Semiconductor Triode", "Solid Triode", "Surface States Triode" [sic], "Crystal Triode" and "Iotatron" were all considered, but "transistor", coined by John R. Pierce, won an internal ballot. The rationale for the name is described in the following extract from the company's Technical Memoranda (May 28, 1948) [26] calling for votes:

Transistor. This is an abbreviated combination of the words "transconductance" or "transfer", and "varistor". The device logically belongs in the varistor family, and has the transconductance or transfer impedance of a device having gain, so that this combination is descriptive.

Improvements in transistor design

[edit]

Shockley was upset about the device being credited to Brattain and Bardeen, who he felt had built it "behind his back" to take the glory. Matters became worse when Bell Labs lawyers found that some of Shockley's own writings on the transistor were close enough to those of an earlier 1925 patent by Julius Edgar Lilienfeld that they thought it best that his name be left off the patent application.

Shockley was incensed, and decided to demonstrate who was the real brains of the operation.[citation needed] A few months later he invented an entirely new, considerably more robust, bipolar junction transistor type of transistor with a layer or 'sandwich' structure, used for the vast majority of all transistors into the 1960s.

With the fragility problems solved, the remaining problem was purity. Making germanium of the required purity was proving to be a serious problem and limited the yield of transistors that actually worked from a given batch of material. Germanium's sensitivity to temperature also limited its usefulness. Scientists theorized that silicon would be easier to fabricate, but few investigated this possibility. Former Bell Labs scientist Gordon K. Teal was the first to develop a working silicon transistor at the nascent Texas Instruments, giving it a technological edge. From the late 1950s, most transistors were silicon-based. Within a few years transistor-based products, most notably easily portable radios, were appearing on the market. "Zone melting", a technique using a band of molten material moving through the crystal, further increased crystal purity.

Metal-oxide semiconductor

[edit]
Main article: MOSFET
See also: Semiconductor device fabrication

In 1955, Carl Frosch and Lincoln Derick accidentally grew a layer of silicon dioxide over the silicon wafer, for which they observed surface passivation effects.[19][20] By 1957 Frosch and Derick, using masking and predeposition, were able to manufacture silicon dioxide field effect transistors; the first planar transistors, in which drain and source were adjacent at the same surface.[21] They showed that silicon dioxide insulated, protected silicon wafers and prevented dopants from diffusing into the wafer.[19][22] At Bell Labs, the importance of Frosch and Derick technique and transistors was immediately realized. Results of their work circulated around Bell Labs in the form of BTL memos before being published in 1957. At Shockley Semiconductor, Shockley had circulated the preprint of their article in December 1956 to all his senior staff, including Jean Hoerni,[23][24][25][26] who would later invent the planar process in 1959 while at Fairchild Semiconductor.[27][28]

1957, Diagram of one of the SiO2 transistor devices made by Frosch and Derick[29]

After this, J.R. Ligenza and W.G. Spitzer studied the mechanism of thermally grown oxides, fabricated a high quality Si/SiO2 stack and published their results in 1960.[30][31][32]Following this research, Mohamed Atalla and Dawon Kahng proposed a silicon MOS transistor in 1959[33] and successfully demonstrated a working MOS device with their Bell Labs team in 1960.[34][35] Their team included E. E. LaBate and E. I. Povilonis who fabricated the device; M. O. Thurston, L. A. D’Asaro, and J. R. Ligenza who developed the diffusion processes, and H. K. Gummel and R. Lindner who characterized the device.[36][37]

With its scalability,[38] and much lower power consumption and higher density than bipolar junction transistors,[39] the MOSFET became the most common type of transistor in computers, electronics,[40] and communications technology such as smartphones.[41] The US Patent and Trademark Office calls the MOSFET a "groundbreaking invention that transformed life and culture around the world".[41]

Bardeen's 1948 inversion layer concept, forms the basis of CMOS technology today.[42] CMOS (complementary MOS) was invented by Chih-Tang Sah and Frank Wanlass at Fairchild Semiconductor in 1963.[43] The first report of a floating-gate MOSFET was made by Dawon Kahng and Simon Sze in 1967.[44] FinFET (fin field-effect transistor), a type of 3D multi-gate MOSFET, was proposed by H. R. Farrah (Bendix Corporation) and R. F. Steinberg in 1967[45] and first built by Digh Hisamoto and his team of researchers at Hitachi Central Research Laboratory in 1989.[46][47]

See also

[edit]

References

[edit]
  1. ^ Golio, Mike; Golio, Janet (2018). RF and Microwave Passive and Active Technologies. CRC Press. p. 18-2. ISBN 9781420006728.
  2. ^ "Who Invented the Transistor?". Computer History Museum. 4 December 2013. Retrieved 20 July 2019.
  3. ^ "Semiconductor Shipments Forecast to Exceed 1 Trillion Devices in 2018". www.icinsights.com. Retrieved 2018-04-16. Annual semiconductor unit shipments (integrated circuits and Opto-sensor-discrete, or O-S-D, devices) are expected to grow 9% [..] For 2018, semiconductor unit shipments are forecast to climb to 1,075.1 billion, which equates to 9% growth for the year. Starting in 1978 with 32.6 billion units and going through 2018, the compound annual growth rate for semiconductor units is forecast to be 9.1%, a solid growth figure over the 40-year span. [..] In 2018, O-S-D devices are forecast to account for 70% of total semiconductor units compared to 30% for ICs.
  4. ^ "13 Sextillion & Counting: The Long & Winding Road to the Most Frequently Manufactured Human Artifact in History". Computer History Museum. April 2, 2018. Retrieved 28 July 2019.
  5. ^ "Gallium nitride semiconductors: The Next Generation of Power | Navitas". 19 March 2021. Retrieved 2023-05-02.
  6. ^ "What is GaN? Gallium Nitride (GaN) Semiconductors Explained". Efficient Power Conversion. Retrieved May 2, 2023.
  7. ^ Hendrik Purwins; Bernd Barak; Ahmed Nagi; Reiner Engel; Uwe Höckele; Andreas Kyek; Srikanth Cherla; Benjamin Lenz; Günter Pfeifer; Kurt Weinzierl (2014). "Regression Methods for Virtual Metrology of Layer Thickness in Chemical Vapor Deposition". IEEE/ASME Transactions on Mechatronics. 19 (1): 1–8. doi:10.1109/TMECH.2013.2273435. S2CID 12369827. Retrieved November 9, 2015.
  8. ^ "8 Things You Should Know About Water & Semiconductors". China Water Risk. 11 July 2013. Retrieved 2023-01-21.
  9. ^ a b c Yoshio, Nishi (2017). Handbook of Semiconductor Manufacturing Technology. CRC Press.
  10. ^ Lei, Wei-Sheng; Kumar, Ajay; Yalamanchili, Rao (2012-04-06). "Die singulation technologies for advanced packaging: A critical review". Journal of Vacuum Science & Technology B, Nanotechnology and Microelectronics: Materials, Processing, Measurement, and Phenomena. 30 (4): 040801. Bibcode:2012JVSTB..30d0801L. doi:10.1116/1.3700230. ISSN 2166-2746.
  11. ^ a b Wang, H. P.; Kim, S. C.; Liu, B. (2014). Advanced FOUP purge using diffusers for FOUP door-off application. 25th Annual SEMI Advanced Semiconductor Manufacturing Conference (ASMC 2014). pp. 120–124. doi:10.1109/ASMC.2014.6846999. ISBN 978-1-4799-3944-2. S2CID 2482339.
  12. ^ a b 450mm FOUP/LPU system in advanced semiconductor manufacturing processes: A study on the minimization of oxygen content inside FOUP when the door is opened. 2015 Joint e-Manufacturing and Design Collaboration Symposium (eMDC) & 2015 International Symposium on Semiconductor Manufacturing (ISSM).
  13. ^ Lin, Tee; Fu, Ben-Ran; Hu, Shih-Cheng; Tang, Yi-Han (2018). "Moisture Prevention in a Pre-Purged Front-Opening Unified Pod (FOUP) During Door Opening in a Mini-Environment". IEEE Transactions on Semiconductor Manufacturing. 31 (1): 108–115. doi:10.1109/TSM.2018.2791985. S2CID 25469704.
  14. ^ Kure, Tokuo; Hanaoka, Hideo; Sugiura, Takumi; Nakagawa, Shinya (2007). "Clean-room Technologies for the Mini-environment Age" (PDF). Hitachi Review. 56 (3): 70–74. CiteSeerX 10.1.1.493.1460. S2CID 30883737. Archived (PDF) from the original on 2021-11-01. Retrieved 2021-11-01.
  15. ^ Kim, Seong Chan; Schelske, Greg (2016). FOUP purge performance improvement using EFEM flow converter. 2016 27th Annual SEMI Advanced Semiconductor Manufacturing Conference (ASMC). pp. 6–11. doi:10.1109/ASMC.2016.7491075. ISBN 978-1-5090-0270-2. S2CID 3240442.
  16. ^ Benalcazar, David; Lin, Tee; Hu, Ming-Hsuan; Ali Zargar, Omid; Lin, Shao-Yu; Shih, Yang-Cheng; Leggett, Graham (2022). "A Numerical Study on the Effects of Purge and Air Curtain Flow Rates on Humidity Invasion Into a Front Opening Unified Pod (FOUP)". IEEE Transactions on Semiconductor Manufacturing. 35 (4): 670–679. doi:10.1109/TSM.2022.3209221. S2CID 252555815.
  17. ^ Lin, Tee; Ali Zargar, Omid; Juina, Oscar; Lee, Tzu-Chieh; Sabusap, Dexter Lyndon; Hu, Shih-Cheng; Leggett, Graham (2020). "Performance of Different Front-Opening Unified Pod (FOUP) Moisture Removal Techniques With Local Exhaust Ventilation System". IEEE Transactions on Semiconductor Manufacturing. 33 (2): 310–315. doi:10.1109/TSM.2020.2977122. S2CID 213026336.
  18. ^ Ernest Braun & Stuart MacDonald (1982). Revolution in Miniature: The History and Impact of Semiconductor Electronics. Cambridge University Press. pp. 11–13. ISBN 978-0-521-28903-0.
  19. ^ a b Huff, Howard; Riordan, Michael (2007-09-01). "Frosch and Derick: Fifty Years Later (Foreword)". The Electrochemical Society Interface. 16 (3): 29. doi:10.1149/2.F02073IF. ISSN 1064-8208.
  20. ^ US2802760A, Lincoln, Derick & Frosch, Carl J., "Oxidation of semiconductive surfaces for controlled diffusion", issued 1957-08-13 
  21. ^ Frosch, C. J.; Derick, L (1957). "Surface Protection and Selective Masking during Diffusion in Silicon". Journal of the Electrochemical Society. 104 (9): 547. doi:10.1149/1.2428650.
  22. ^ Frosch, C. J.; Derick, L (1957). "Surface Protection and Selective Masking during Diffusion in Silicon". Journal of the Electrochemical Society. 104 (9): 547. doi:10.1149/1.2428650.
  23. ^ Moskowitz, Sanford L. (2016). Advanced Materials Innovation: Managing Global Technology in the 21st century. John Wiley & Sons. p. 168. ISBN 978-0-470-50892-3.
  24. ^ Christophe Lécuyer; David C. Brook; Jay Last (2010). Makers of the Microchip: A Documentary History of Fairchild Semiconductor. MIT Press. pp. 62–63. ISBN 978-0-262-01424-3.
  25. ^ Claeys, Cor L. (2003). ULSI Process Integration III: Proceedings of the International Symposium. The Electrochemical Society. pp. 27–30. ISBN 978-1-56677-376-8.
  26. ^ Lojek, Bo (2007). History of Semiconductor Engineering. Springer Science & Business Media. p. 120. ISBN 9783540342588.
  27. ^ US 3025589  Hoerni, J. A.: "Method of Manufacturing Semiconductor Devices” filed May 1, 1959
  28. ^ US 3064167  Hoerni, J. A.: "Semiconductor device" filed May 15, 1960
  29. ^ Frosch, C. J.; Derick, L (1957). "Surface Protection and Selective Masking during Diffusion in Silicon". Journal of the Electrochemical Society. 104 (9): 547. doi:10.1149/1.2428650.
  30. ^ Ligenza, J. R.; Spitzer, W. G. (1960-07-01). "The mechanisms for silicon oxidation in steam and oxygen". Journal of Physics and Chemistry of Solids. 14: 131–136. doi:10.1016/0022-3697(60)90219-5. ISSN 0022-3697.
  31. ^ Deal, Bruce E. (1998). "Highlights Of Silicon Thermal Oxidation Technology". Silicon materials science and technology. The Electrochemical Society. p. 183. ISBN 978-1566771931.
  32. ^ Lojek, Bo (2007). History of Semiconductor Engineering. Springer Science & Business Media. p. 322. ISBN 978-3540342588.
  33. ^ Bassett, Ross Knox (2007). To the Digital Age: Research Labs, Start-up Companies, and the Rise of MOS Technology. Johns Hopkins University Press. pp. 22–23. ISBN 978-0-8018-8639-3.
  34. ^ Atalla, M.; Kahng, D. (1960). "Silicon-silicon dioxide field induced surface devices". IRE-AIEE Solid State Device Research Conference.
  35. ^ "1960 – Metal Oxide Semiconductor (MOS) Transistor Demonstrated". The Silicon Engine. Computer History Museum. Retrieved 2023-01-16.
  36. ^ KAHNG, D. (1961). "Silicon-Silicon Dioxide Surface Device". Technical Memorandum of Bell Laboratories: 583–596. doi:10.1142/9789814503464_0076. ISBN 978-981-02-0209-5.
  37. ^ Lojek, Bo (2007). History of Semiconductor Engineering. Berlin, Heidelberg: Springer-Verlag Berlin Heidelberg. p. 321. ISBN 978-3-540-34258-8.
  38. ^ Motoyoshi, M. (2009). "Through-Silicon Via (TSV)" (PDF). Proceedings of the IEEE. 97 (1): 43–48. doi:10.1109/JPROC.2008.2007462. ISSN 0018-9219. S2CID 29105721. Archived from the original (PDF) on 2019-07-19.
  39. ^ "Transistors Keep Moore's Law Alive". EETimes. 12 December 2018. Retrieved 18 July 2019.
  40. ^ "Dawon Kahng". National Inventors Hall of Fame. Retrieved 27 June 2019.
  41. ^ a b "Remarks by Director Iancu at the 2019 International Intellectual Property Conference". United States Patent and Trademark Office. June 10, 2019. Retrieved 20 July 2019.
  42. ^ Howard R. Duff (2001). "John Bardeen and transistor physics". AIP Conference Proceedings. Vol. 550. pp. 3–32. doi:10.1063/1.1354371.
  43. ^ "1963: Complementary MOS Circuit Configuration is Invented". Computer History Museum. Retrieved 6 July 2019.
  44. ^ D. Kahng and S. M. Sze, "A floating gate and its application to memory devices", The Bell System Technical Journal, vol. 46, no. 4, 1967, pp. 1288–1295
  45. ^ Farrah, H. R.; Steinberg, R. F. (February 1967). "Analysis of double-gate thin-film transistor". IEEE Transactions on Electron Devices. 14 (2): 69–74. Bibcode:1967ITED...14...69F. doi:10.1109/T-ED.1967.15901.
  46. ^ "IEEE Andrew S. Grove Award Recipients". IEEE Andrew S. Grove Award. Institute of Electrical and Electronics Engineers. Archived from the original on September 9, 2018. Retrieved 4 July 2019.
  47. ^ "The Breakthrough Advantage for FPGAs with Tri-Gate Technology" (PDF). Intel. 2014. Archived (PDF) from the original on 2022-10-09. Retrieved 4 July 2019.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Semiconductor_device&oldid=1251460278"